tgl41-6.8a thru tgl41-200a www.vishay.com vishay general semiconductor revision: 11-dec-12 1 document number: 88403 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 t rans zorb ? transient voltage suppressors features ? plastic melf package ? ideal for automated placement ? glass passivated chip junction ? available in uni-directional polarity only ? 400 w peak pulse powe r capability with a 10/1000 s waveform, repetitive rate (duty cycle): 0.01 % ? excellent clamping capability ? very fast response time ? low incremental surge resistance ? meets msl level 1, per j-st d-020, lf maximum peak of 250 c ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 typical applications use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ics, mosfet, signal lines of sensor units for consumer, computer, industrial, and telecommunication. mechanical data case: do-213ab (gl41) molding compound meets ul 94 v-0 flammability rating base p/n-e3 - rohs compliant, commercial grade terminals: matte tin plated leads, solderable per j-std-002 and jesd 22-b102 e3 suffix meets jesd 2 01 class 1a whisker test polarity: blue band denotes the cathode which is positive with respect to the anode under normal tvs operation notes (1) non-repetitive current pulse, per fig. 3 and derated above t a = 25 c per fig. 2. rating is 200 w above 91 v (2) measured at 8.3 ms single half sine-wave or eq uivalent square wave duty cycle = 4 pulses per minute maximum primary characteristics v br uni-directional 6.45 v to 210 v v wm 5.8 v to 171 v p ppm 400 w, 200 w p d 1.0 w i fsm 40 a t j max. 150 c polarity uni-directional package do-213 ab (gl41) do-213ab (gl41) maximum ratings (t a = 25 c unless otherwise noted) parameter symbol value unit peak pulse power di ssipation with a 10 /1000 s waveform (1) (fig. 1) p ppm 400 w power dissipation on infinite heatsink at t l = 75 c p d 1.0 w peak pulse current with a 10/1000 s waveform (1) (fig. 3) i ppm see next table a peak forward surge current, 8.3 ms half sine-wave uni-directional only (2) i fsm 40 a maximum instantaneous forward voltage at 25 a for uni-directional only v f 3.5 v operating junction and storage temperature range t j , t stg - 55 to 150 c
tgl41-6.8a thru tgl41-200a www.vishay.com vishay general semiconductor revision: 11-dec-12 2 document number: 88403 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes (1) pulse test: t p ? 50 ms (2) surge current waveform per fig. 3 and derate per fig. 2 (2) all terms and symbols are consis tent with ansi/ieee c62.35 electrical characteristics (t a = 25 c unless otherwise noted) device type breakdown voltage v br (1) (v) test current i t (ma) stand-off voltage v wm (v) maximum reverse leakage at v wm i d (a) maximum peak pulse current i ppm (2) (a) maximum clamping voltage at i ppm v c (v) maximum temperature coefficent of v br (%/c) min. max. tgl41-6.8a 6.45 7.14 10 5.80 1000 38.1 10.5 0.060 tgl41-7.5a 7.13 7.88 10 6.40 500 35.4 11.3 0.064 tgl41-8.2a 7.79 8.61 10 7.02 200 33.1 12.1 0.068 tgl41-9.1a 8.65 9.55 1.0 7.78 50.0 29.9 13.4 0.071 tgl41-10a 9.5 10.5 1.0 8.55 10.0 27.6 14.5 0.076 tgl41-11a 10.5 11.6 1.0 9.40 5.0 25.6 15.6 0.078 tgl41-12a 11.4 12.6 1.0 10.2 5.0 24.0 16.7 0.081 tgl41-13a 12.4 13.7 1.0 11.1 5.0 22.0 18.2 0.084 tgl41-15a 14.3 15.8 1.0 12.8 5.0 18.9 21.2 0.087 tgl41-16a 15.2 16.8 1.0 13.6 5.0 17.8 22.5 0.089 tgl41-18a 17.1 18.9 1.0 15.3 5.0 15.9 25.2 0.091 tgl41-20a 19.0 21.0 1.0 17.1 5.0 14.4 27.7 0.093 tgl41-22a 20.9 23.1 1.0 18.8 5.0 13.1 30.6 0.095 tgl41-24a 22.8 25.2 1.0 20.5 5.0 12.0 33.2 0.097 tgl41-27a 25.7 28.4 1.0 23.1 5.0 10.7 37.5 0.099 tgl41-30a 28.5 31.5 1.0 25.6 5.0 9.7 41.4 0.100 tgl41-33a 31.4 34.7 1.0 28.2 5.0 8.8 45.7 0.101 tgl41-36a 34.2 37.8 1.0 30.8 5.0 8.0 49.9 0.102 tgl41-39a 37.1 41.0 1.0 33.3 5.0 7.4 53.9 0.103 tgl41-43a 40.9 45.2 1.0 36.8 5.0 6.7 59.3 0.104 tgl41-47a 44.7 49.4 1.0 40.2 5.0 6.2 64.8 0.104 tgl41-51a 48.5 53.6 1.0 43.6 5.0 5.7 70.1 0.105 tgl41-56a 53.2 58.8 1.0 47.8 5.0 5.2 77.0 0.106 tgl41-62a 58.9 65.1 1.0 53.0 5.0 4.7 85.0 0.107 tgl41-68a 64.6 71.4 1.0 58.1 5.0 4.3 92.0 0.107 tgl41-75a 71.3 78.8 1.0 64.1 5.0 3.9 103 0.108 tgl41-82a 77.9 86.1 1.0 70.1 5.0 3.5 113 0.108 tgl41-91a 86.5 95.5 1.0 77.8 5.0 3.2 125 0.109 tgl41-100a 95.0 105 1.0 85.5 5.0 1.46 137 0.109 tgl41-110a 105 116 1.0 94.0 5.0 1.32 152 0.110 tgl41-120a 114 126 1.0 102 5.0 1.21 165 0.110 tgl41-130a 124 137 1.0 111 5.0 1.12 179 0.110 tgl41-150a 143 158 1.0 128 5.0 0.97 207 0.111 tgl41-160a 152 168 1.0 136 5.0 0.91 219 0.111 tgl41-170a 162 179 1.0 145 5.0 0.85 234 0.111 tgl41-180a 171 189 1.0 154 5.0 0.81 246 0.111 tgl41-200a 190 210 1.0 171 5.0 0.73 274 0.111 ordering information (example) preferred pin unit weight (g) preferred package code base quantity delivery mode tgl41-6.8a-e3/96 0.134 96 1500 7" di ameter plastic tape and reel tgl41-6.8a-e3/97 0.134 97 5000 13" di ameter plastic tape and reel
tgl41-6.8a thru tgl41-200a www.vishay.com vishay general semiconductor revision: 11-dec-12 3 document number: 88403 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 ratings and characteristics curves (t a = 25 c unless otherwise noted) fig. 1 - peak pulse power rating curve fig. 2 - pulse power or current vs. initial junction temperature fig. 3 - pulse waveform fig. 4 - typical junction capacitance fig. 5 - power derating curve fig. 6 - maximum non-repetitive peak forward surge current uni-directional only t d - p u lse width 100 10 1 0.1 p ppm - peak p u lse po w er (kw) 0.1 s 1.0 s 10 s 100 s 1.0 ms 10 ms tgl41-100 tgl200a tgl41-6.8 tgl91a n on-repetiti v e p u lse wa v eform sho w n in fig. 3 t a = 25 c t j - initial temerat u re (c) 100 50 25 0 peak p u lse po w er (p pp ) or c u rrent (i pp ) derating in percentace (%) 02550 100 150 200 75 75 125 175 t - time (ms) 150 50 0 0 2.0 4.0 i ppm - peak p u lse c u rrent, % i rsm 100 1.0 3.0 peak val u e i ppm 10/1000 s wa v eform as defined b y r.e.a. half val u e - i ppm i pp 2 t j = 25 c p u lse width (t d ) is defined as the point w here the peak c u rrent decays to 50 % of i ppm t r = 10 s t d meas u red at stand-off voltage v wm v br - breakdo w n voltage (v) 10 000 1000 100 10 c j - j u nction capacitance (pf) 1 10 100 1000 uni-directional meas u red at zero bias t j = 25 c f = 1.0 mhz v sig = 50 mv p-p t l - lead temerat u re (c) 1.00 0.50 0.25 0 p d - po w er dissipation (w) 02550 100 150 200 0.75 75 125 175 nu m b er of cycles at 60 hz 50 10 0 1100 peak for w ard s u rge c u rrent (a) 40 10 30 20 t j = t j max. 8.3 ms single half sine-wa v e
tgl41-6.8a thru tgl41-200a www.vishay.com vishay general semiconductor revision: 11-dec-12 4 document number: 88403 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package outline dimensions in inches (millimeters) d1 = 0.105 0.095 (2.67) (2.41) + 0 - 0.008 (0.20) d2 do-213ab (gl41) soldera b le ends 1 st band d2 = d1 1 st band denotes type and positi v e end (cathode) 0.138 (3.5) max. 0.049 (1.25) mi n . 0.118 (3.0) mi n . 0.238 (6.0) ref. mounting pad layout 0.022 (0.56) 0.018 (0.46) 0.022 (0.56) 0.018 (0.46) 0.205 (5.2) 0.185 (4.7)
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
